Відео

Gonna go 100 cell

I got me some

By speedometer? Fo' real, Homie? :-D

also one Good Tip, dont use Hockey Pucks use an Rubber Block and then nothing should slide away !

I'm hyper paranoid about jacks doing things that they shouldn't after having a scissor jack twist and break on me and having the pos jack that came with my E46 BMW break when the little plastic piece broke, resulting in my fingers getting smashed in between the rear fender and the rear wheel that I'd just taken totally off but was still in thw wheel well. Luckily for the car but not for my fingers the car fell just right to where it was resting on that wheel, with my fingers stuck in between the wheel and the fender. I was able to lift the car just enough with my free arm to slide my hand out. Now every time I jack a car up I'm on thw ground watching exactly what the jack is doing and I'll also have a second jack, a scissor jack or a bottle jack that's a backup for the floor jack. Every inch or so I'll raise the backup to match the floor jack. I also don't trust those "lips". I find a spot on the frame or maybe a control arm.

Look at the ground also.......

You are just showing people how much you don't know lol

Who the hell uses spacers on a jack lol that's why it happened..........

What was the line that you moved from the power steering res? The one you though was a cooling line.

This video does help and thank you for sharing. I'm sick of playing the "drive my car up on 2 wedges simultaneously so I can change the oil" game. So I'm looking for a good floor jack that doesn't constantly lose hydraulic pressure and fall before I can get the stands under the car (any suggestions?).

Ceramic coat wan't reduce the heat... increase the heat...more the gas is hot more fast will be the flow and better performance. 🤪👋

That's gonna leave a mark.

This is the only video online of this kind. Thank you! Since your new injector values were exactly the same as the old ones did you really need to do the ISTA steps? My S63TU3 is misfiring in one of my cylinders (6) at idle only and I want to DIY just that one. My issue is that I don’t have access to ISTA

Moral of the story...buy a house worth more than your car so you dont have a shit garage floor. Honestly, that the worst garage floor i have ever seen.

To avoid somthing like this in the future using scrap blocks of wood 2x4 and 4x4 instead of hockey pucks is much more stable if you need spacing like in the video. Also if you have ramps under the back like this lift the front all at once from the front not the sides like that and you will avoid some funky twisting and slippage. Lastly the surface where the jack is riding is very important to be smooth!!! The jack needs to roll as it goes up to stay where it needs to be on the car!!! Very important!! Hope everyone body stays safe and has a good day!!!

Good for you for talking about this. I’ve seen it 100 times around the web - it’s good to know that inters just the side skirt that was damaged… most of the clips I’ve seen are cropped and edited so that it looks like you did structural damage. Anyway, the great attitude is refreshing to see - thank you!

Its because you forgot the third puck jejeje(theres a jack that has a screw up lift pad it raises it up )

use a block of wood next time .

sux man erryone's a keyboard warrior until they make a mistake. seksi wheels btw

Get another Lexus! LC500 or ISF!!! The Lexus world needs you!!!

How much did reparations cost you ?

The issue is you ut a car on ramps then tried to jack up one side of the front of the car . Not a good way to do that. Rather jack the car from the front so the car lifts even and less chance of the car moving off the ramps. Then put jack stands under the car and lower it onto them a much safer way to work on a car in the air.

I understand this completely. My isf is the same way as well as my evo 9

Expensive lesson…..

I mean it's a nice idea but iv been jacking cars up most my life I go straight for the brace in the wheel where the jack stands go in the hole I bypass all the pinch welds lol or if I'm lucky I get fork lift under the whole thing with some silicone bed on it or something

Self inflicted through stupidity .

I hope you're doing better now. I'm in the middle of a valium taper rn. About half way through and yeah. Cutting that much that fast just would not be possible for me either. Even going slowly is awful enough. I'm at 6mg of valium and just that will take me another 6 months or so.

The right tool, is never too expensive.

I have an M5 competition. After the downpipe installation, white smoke has started to come when the engine warms up. only when gas is applied and released. Can't see that it uses cooler fluid. I think the oil consumption is normal. What do you think it could be? Anyone else here with experience?

finally you are back :D

Your jack needs a head that works for your car, they sell ones with tall heads for cars like this, you need to get one and never use hockey pucks again.

You just opened yourself up for a whole new lot of "What you did wrong..." It's YT bro, everyone's an expert.

I am glad you didn't get hurt, it's just an expensive lesson that we all can learn from.

Remove the skirt and use 1 puck... also, your floor is super rough and doesnt allow the jack to move properly. You need a flat surface.

Looked like the problem was the jack moving while you were jacking it up.

Is the superfast charging working?

Use the right tools, hockey pucks are for hockey.

You simply don't know what you're doing. Stop before you hurt yourself.

Peel that screen protector off and your touches will be flawless.

lmao hockey pucks.....how stupid can you be

Thank you for the intel.

I'm sorry this happened to you. Omg.

I see a puddle of uneven concrete at 2:00 🤔

Any news for the LC 500 🙏🏼🙏🏼🙏🏼 turbo, supercharger?

Faaack you remind me of my exwife. Even when you know you fked up you still won’t admit it and try to be right

I'm sorry that happened to you. We all make mistakes even though some of us like to pretend otherwise.

Great content thank you for sharing

Сделано очень плохо. Сейчас есть более аккуратные решения.

Why did you shake the bottle.??

should of kept the GS - F . you gone regret it .